CRUSHING SPREAD
4-1/4 Symons cone crusher
-c-41841-48’Lx9’10Wx14’H and (21’H with tower up)
-approximate a 1954 4-1/4 standard head unbalanced cone crusher 200hrs on cone since “complete rebuild” Inc bowl and mantle and wear saddles and plates replaced
-cone is rubber mounted
-hewitt robins 5x16 screening surface, triple deck completely rebuilt may 2006. Deck is 5.5’x19’ long not including chute.
-screen deck model #td-lpe-11
-30hp motor on screener
--product belt 42” wide 3 ply ¼ top winged tail pulley head pulley lagged &chain drive 10hp motor
--under slung cone belt 42” 3 ply ¼ top
-2 e stops & guarded winged tail pulley lagged head pulley 10hp motor
-cat walk around cone &screener deck
-manual raise &lower control tower
-all controls, heater and air conditioner in tower, soft start and disconnect for 200hp cone in tower also 120v breaker panel and external sodium light
-cone lube pumps are electric and mechanical, oil heater, oil cooling fan, filter, temp gauges ,oil sensors for temp flow and presser are all done to spec for cone oil
-main disconnect, starters are mounted on the side of the crusher including frequency drive for buggy bin and 110 volt plug gins for lights
-all electrical done professionally front right has plugs for conveyors
-chassis has solid legs for blocking
-screening deck and railing has to be removed and control tower lowered for transportation
-3 axle chassis
-screening deck approximate weight 8 tons cone chassis approximate 60 ton
30’ STACKER
-manual raise and lower no side travel
-34’Lx8’wx9’h in down position
-36” belt 3 ply 3/16 top
-2 e stops & guarded
-hopper 7’L x27” w with flashing
-side rails the length of the belt
-manual lift
-tires 11r 22.5
-dodge txt4a gearbox
-motor 10 hp new June 2005
-winged tail pulley
-impact rollers under hopper
-2 drive belts b77
-approximate weight 5 ton
GENERATOR VAN
-48’ van that was professionally built by Kramer tractor ltd- 500 gallon fuel tank new in 2005 double wall mounted at front of generator van with external venting and fueling connections. Trailer has 2 large ventilation louvers on both sides of the front 3’x6’ that open and close.
-switch gear Inc main disconnect that can be hard wired for use without generator power to run spread. 2- 200 amp disconnects, 1- 15kva transformer, and all disconnects and spares needed for existing spread. 1- 15hp frequency drive for vibrating feeder 120v breaker panel, oil fired furnace
-small work bench, air compressor, and fire suppression system (needs to be serviced) but never used.
--generator is a caterpillar d3248 engine rebuilt in 2005 (it had reached its wear specs) it is also equipped with electronic protection for low oil pressure and has a block heater.
-12 cylinder ser# 36j912
-all crusher voltage is 3 phase 575v 60hrz
-the generator puts out 722 amp 750 kva
-generator was rebuilt and dipped 2005
-caterpillar engine is cooled by an external radiator, which has 4, 25’ hoses that connect to the side of the gen trailer
-radiator weighs aprox 6 tons and is about 8 feet square and sits on the ground and has two 15 hp fans that keep it cool
105’ STACKER
-108’Lx10’Wx14’H down
-30” belt 4 ply 1/8 top (fair shape)
-2 e stops guarded
-hopper 10’Lx3’W
-20’ of side rails
-hyd raise 11/2hp
-manual wheels &side movement
-impact rollers under hopper
-dodge txt6 gear box
-belts 3 c138
-center drive lagged
-winged tail pulley (new bearings 2004)
-approximate weight 12 ton
40’ THOR INCLINE BELT
-41’Lx5’Hx5’6w
-42” belt 3ply 3/16 top
-2 e stops& guarded
-hopper 4’Lx3’Wwith flashing
-side rails the length of the belt
-square tube legs manual lift with pins
-dodge txt5 gear box
-motor 15 hp older WEG
-2 drive belts b size
- Impact rollers under hopper
-tail pulley is smooth pulley
-approximate weight 4 ton